6 Hole Vertical Channel for Weld On Tongue Adapter for A-Frames - Channel Only - Vertical Channel is 3-1/2" x 11-3/4" w/ 2" on center bolt pattern
$52.08
or as low as $5/mo with flexible financing — 4, 6, or 12 months. Options at checkout.
Looking for a full weld
on vertical channel adapter, check out our Shocker Hitch Vertical Channel Weld On Tongue Adapter for Trailer A-Frames
Works with our trailer tongue
mount air hitches or 5/8″ bolt on vertical channel mount trailer couplers & pintle rings.
6 Adjustment Holes
That use 5/8″ pins or 5/8″ x 4-1/2″ bolts to secure trailer coupler or pintle ring.
Weld on Vertical Channel
Actual vertical channel is 3-1/2″ x 11-3/4″ w/ 2″ on center bolt pattern.
Stop destroying your trailer and cargo.
Every bump, pothole, and expansion joint sends a violent jolt through your trailer frame, damaging cargo and wearing out your truck. Shocker Air Ride Hitches absorb that punishment at the coupling, before it reaches your trailer.
When your coupler or pintle ring sits at the wrong height, every hookup turns into a fight and the whole ride pays for it because nothing lines up the way it should. This heavy duty weld-on vertical channel gives your trailer A-frame a solid, adjustable place to mount up. The channel runs 3-1/2" x 11-3/4" with a 2" on-center bolt pattern, and its 6 adjustment holes let you set the coupler or pintle at the right height instead of settling for close enough. You lock it in with 5/8" pins or bolts, and once it's professionally welded to the A-frame it carries up to 20,000 lbs GTW. It's built for our air trailer tongue mount couplers and pintle rings, and it ships in raw steel ready for your welder.
Key Highlights
- 3-1/2" x 11-3/4" weld-on channel with a 2" on-center bolt pattern for a clean, square mount.
- 6 adjustment holes dial coupler or pintle height, locked with 5/8" pins or 5/8" x 4-1/2" bolts.
- Heavy duty raw steel, unfinished and ready to weld.
- Carries up to 20,000 lbs GTW once it's professionally welded on.
- Fits our trailer tongue mount air hitches and 5/8" bolt-on vertical channel couplers and pintle rings.
- Need the complete adapter? Check our Shocker Hitch Vertical Channel Weld On Tongue Adapter for Trailer A-Frames.
Installation
Watch the official install walkthrough for this hitch — the exact steps and tools, straight from the manufacturer.
What It Works With
- Pairs with our trailer tongue mount air hitches, plus any 5/8" bolt-on vertical channel coupler or pintle ring.
Specs and What They Do for You
- 3-1/2" x 11-3/4" vertical channel with a 2" on-center bolt pattern, so your coupler lands square and where you need it.
- 6 adjustment holes let you set coupler or pintle height, then lock it down with 5/8" pins or 5/8" x 4-1/2" bolts.
- Heavy duty raw steel, unfinished so your welder can bite in clean.
- Rated up to 20,000 lbs GTW once professionally welded, so it holds when the load rides heavy.
- Want the full weld-on adapter instead of the channel by itself? See our Shocker Hitch Vertical Channel Weld On Tongue Adapter for Trailer A-Frames.
When Hardware Wears Out or Walks Off
Mounting bolts, pins, plates, and shackles get lost or wear down after enough miles. These OEM-spec kits drop in as exact replacements, so your Shocker hitch goes back together the way it was engineered to.
$52.08
Still researching?
Skip the product wall — these are the four guides every buyer actually opens before they decide.
Installation Guide
Step-by-step videos for every Shocker family. What's in the box, what tools you need, and how long it takes.
Watch the installAir Pressure Setup
How to dial in air pressure by trailer weight so the ride is right the first time and the hitch lasts longer.
See psi by loadTowing Capacity Guide
Match GTW, tongue weight, and receiver size to your truck class so you don't over- or under-buy.
Read the guideConfigure Your Hitch
60-second fit quiz — answer a few questions about your truck and trailer, get a tailored recommendation.
Start the quiz
- 1-Year Manufacturer Warranty
- 60-Day Returns
- 20,000+ Customers
- Ships from Canada
